[c/f]

The Twisted Revolta I paraded for 2022 with a 90g 4s setup,

I have really been liking the APC indoor 3D profile props but they are low rpm range torquey so I repowered this back to a 3s 67g powerplant setup on an 18amp ESC and flight timer is now 5:30min with 18% remaining.

T-Motor 1100KV

https://www.getfpv.com/motors/commercial-cinematography-motors/t-motor-f100-2810-lr-cinematic-motor-1100kv-1350kv.html

10x4.6SF - APC Propellers

Slow Flyer Indoor 3D (SF3D) For Indoor 3D Aerobatics Use LPAR18SF or LPARM12SF adapter rings Includes one set of rings from LPARM12SF

www.apcprop.com

FWIW the APC Indoor 3D profile style is available now in sizes 6"-12" and pitches are 3.8, 4.1, 4.6
These are perfect to keeps speeds down and gyro gains high.............

 

[BalsaDust]

I've been looking for a better setup for my revolto. Got any videos of it with this new setup?

 

[McDDD]

So does this new Revolto setup fly better than the one I flew at Ottumwa a couple years ago?

 

[c/f]

To me it does, by running a smaller prop and lower pitch really lets it crank tight KE spins and tumbles, when you get the throttle jokey just right it becomes a blurr. I was 3s back when you flew it on 11X5 Graupner. I think you would notice a differance on yours just trying that 10X4.6.
My grandsons is 1000KV and mine 1100kv, he does not like mine because he is so used to his throttle as a control surface he is off in response after 3 years his is still pristine with no repairs. Mines got lots of repairs trying to keep landing gear in place...

The 4s I had on 980KV and I used a 9X4.1 APC 3D as the 9X4.6 you could even tell the differance in KE spins and Tumbles... My flight times were only at 4:30min.

 

[McDDD]

I think I might have a 10x4.7 SF laying around somewhere. If so, I'll give it a try.
Thanks!

 

[c/f]

No No No,,, These are the retooled APC INDOOR 3D blade design. They really have a low torq kick to them.
These retooled blades APC now has in a host of sizes and are now my favorites go toos on all my foamies..............

6X3.1
6X4.1
7X4.1
8X4.1
9X4.1 9X4.6
10X3.8 10X4.6
11.4.6
12X3.8

 

[McDDD]

Ahh HAA!
That makes more sense!
I'll have to check those out.

 

[BalsaDust]

I have some of the 9x4.1 on my crack fokker and crack beaver. They are very delicate and can't take a hit but they do pull hard down low.

 

[wyo69cowboy]

No No No,,, These are the retooled APC INDOOR 3D blade design. They really have a low torq kick to them.
These retooled blades APC now has in a host of sizes and are now my favorites go toos on all my foamies..............

6X3.1
6X4.1
7X4.1
8X4.1
9X4.1 9X4.6
10X3.8 10X4.6
11.4.6
12X3.8

They feel like a cross between a regular APC e prop and the APC slow flyers--which is really what they look like anyway, in profile. I really like them. I too have a Twisted Fokker, on a kinda lazy 2S setup--I was using a 9x4.7 slowfly for quite a while, and switched to the 9x4.6 3D slowfly, and it really added throttle response and punch. Bonus was slightly more flight time

 

[bajajrider]

has anybody tried the apc Multi Rotor props ? profile looks interesting and thin, but not as thin like the SF props.
might have to pull the trigger on some 9x4.5 and 11x5.5's to try out.

 

[c/f]

I liked the 13X5.5 MR on 40 sized slab 4s

 

[Straightup]

Thank you for that info Mike